blunt tubes

[B-Rye-oNeR]

could someone tell me the sizes of tubing needed to make those blunt tube things and also where to get the rubber grommets to hold them together, I think the inside one was 9.5,.?.?

[NUBBLET]

12 mil standard ? ace hardware for grommets .

[hippi]

blunt tube?..like a glass mouth piece for a blunt?

[ALIEN!]

11mm X 1.5mm Simax Clear Tubing
15mm X 1.8mm Simax Clear Tubing

[ALIEN!]

oh yeah, and use some 3/4" heat shrink tubing, about a 1 1/4" length on the joint for a seal. Make sure its NOT the adhesive lined stuff.

Here (http://cgi.ebay.com/100-FT-Roll-3-4-Black-Polyolefin-Heat-Shrink-Tubing_W0QQitemZ110446185935QQcmdZViewItemQQptZLH_ DefaultDomain_0?hash=item19b71b0dcf)

[hippi]

again...blunt tubes??

[NUBBLET]

smokeless cigarettes , check the head shop . tube slides in other tube , you pack larger tube and slide the inner up as the top burns out , short version .

[Lub]

commonly called glass blunt or a slider sometimes

[gn0me]

From a google search, what I could find was this:
http://www.spaceweed.com/il_430xN_12598323.jpg
Hotlinked from http://www.spaceweed.com/Glass_Blunt.html

Apparently, it's a glass tube with another flared glass tube inside it to act as a plunger, connected with some shrink tubing. The plunger/mouthpiece part is pulled back until the desired amount of room is available, then the big tube is filled with "tobacco" and lit. As it burns, the plunger is pushed forward to ash the blunt and keep the "tobacco" cherried. I've never tried one, but from what I've read, they are reported to smoke similar to real blunts or handrolled "cigarettes", but they hold a very large amount - 2 grams of "tobacco" or more... great for parties!

As with any glass for smoking, its important to keep them clean.

[hippi]

thats pretty crazy...weird that ive never heard of these...ive proly seen them at the smoke shops but proly thought they were a crack pipe lol..

[RamblezMarblez]

Who buy'z these blunt pipes? I know if I showed up with one of these in the hood, the brothers would laugh at me. However the one dude who bought a unicorn pipe might be interested...........

[byron3]

Well we give our customers a little better value 10mm & 16mm, use a rubber grommet not heat shrink.

[3ripmin]

blunt tube?..like a glass mouth piece for a blunt?

this is what i thought the op was asking about. i heard about them a few weeks ago.

i think theyre like a glass crutch with a flat mouth piece.

[B-Rye-oNeR]

thanks ! yeah they are pretty ugly, and crackish, I saw a dude at roo unlodaing them last year, I have had some requests for them, don't know if there're worth messin with.

[CripSkillz]

my shop buys them and they are a easy 15 $..

[ModderXtr]

I make glass mouthpieces for blunts, theyre like chillums but shorter and I don't close the reduction as small as I would on a regular chillum. I do a reduction to about the diameter of a blunt mouthpiece in a 3 or 4 inch long section of 12mm tube.

[B-Rye-oNeR]

hey, coupple more qs, how long do you gennerally make them, and 15 dollars wholesale?!

[Fiorino Glass Art]

Yeah yeah, glass blunts!! I've had people ask me to make em one, well couple friends. I just tell em to roll it! Plus seems like you'd have to clean it after everytime you use it.

[byron3]

Outer tube 3", wholesale from the distributors are around $10.00....... I make these (out of hvy tubing and full color mouthpiece) and only retail them for $24.95.

[AgentChesterDesmond]

thanks ! yeah they are pretty ugly, and crackish, I saw a dude at roo unlodaing them last year, I have had some requests for them, don't know if there're worth messin with.

hmmmm....i was selling them at roo last year.

[B-Rye-oNeR]

the dude i saw rockin them said he didn't make them, his bro did or somethin, (they were small ones, coupple of them said roo on the flat mouthpiece,) Thanks for all the info tho!

[GlassFreak]

i have one, dont use it any more really but i used to a lot. works good. never made any but i would think they would be easy as hell. its just getting the 2 tubes different sizes and a little piece of shrink tube. the one i have isnt even flared, just a little stringer across the inside tube so theres something to pack it against.

[B-Rye-oNeR]

so u just put them in the kiln on 250 or lower to shrink the "heat shrink" tubing? OR?.....tried a hairdryer, didnt work too well.

[berning]

heat gun , like one for stripping paint.

[AgentChesterDesmond]

good idea berning.....I just use a HH with a really low flame.

[CripSkillz]

or a bic lighter bout a inch under it..

[B-Rye-oNeR]

yeah i ended up using torch worked well, after i figured out where to hold it, thanks theses things are money...helps keep my shop running. IM paying for whole shop now so every dollar counts. anyone use colored tubings'? might look nice

[AgentChesterDesmond]

i usually make them with green china tube

[peteypuff]

When you use standard wall tubing, what is the best way to get clean ends? I havent had much luck scoring.

[playa00]

These are great what size tubing for inner outer I have found the rubber grommets just would like to get an idea on size of tubes so I can start prodo. These better than chilliums I assume constrictions and ice pinch is getting old lol

[Aaron Ellis]

http:// http://www.king-tool.com/img/tools/tool-groups/480/scribes-group.jpg

I just score with w concrete scribe and snap to size. ^^