**HUGE** DHG Winter Tool Sale

[Dawg House Glass]

Introducing our Our Winter X-mas sale on all Dawg House Glass tool in the line up. This sale starts now and ends on 12/15. All of our tools are made here in Reno Nevada so yes all 100% MADE IN USA tools here made by a glass blower for the glass blower.

Female 19mm and 14mm joint shaping tools
19mm brass OG 10:1 joint shaping tool $90 ***SALE PRICE $70***
(comes with a 5/8" brass handle with built in 5/8" push on the end)
14mm brass Lil OG 10:1 joint shaping tool $90 ***SALE PRICE $70***
(comes with a 1/2" brass handle with built in 1/2" push on the end)

Sophie tools
4mm-19mm hollow cone shape tool with 8" stainless steel hollow blow tube handle available in either smooth or octagon cut. $65 *** SALE PRICE $50***


Reamers
1/2" brass reamer 2mm-12mm 5" long $40 **SALE PRICE $30**
1/2" brass reamer 6mm-12mm 3" long $40 **SALE PRICE $30**
3/4" brass reamer 2mm-19mm 5" long $45 **SALE PRICE $35**
3/4" brass reamer 8mm-19mm 3" long $45 **SALE PRICE $35**
3/4" brass reamer 2mm-19mm 2" long $45 **SALE PRICE $35**
1" brass reamer 2mm-25mm 5" long $65 **SALE PRICE $55**
1" brass reamer 14mm-25mm 3" long $65 **SALE PRICE $55**
1" brass reamer 2mm-25mm 2" long $65 **SALE PRICE $55**

BOWL PUSHES
1/2" brass bowl push round (no tip) $35 **SALE PRICE $28**
1/2" brass bowl push w/tip $35 **SALE PRICE $28**
5/8" brass bowl push round (no tip) $37 **SALE PRICE $30**
5/8" brass bowl push w/tip $37 **SALE PRICE $30**
3/4" brass bowl push round (no tip) $40 **SALE PRICE $32**
3/4" brass bowl push w/tip $40 **SALE PRICE $32**


Well here she is folks. I was thinking now how is everyone going to know they have a Dawg House Glass jig with all the different ones being made these days both good and well not so good jigs but either way now you all have a way to know who to love when you use a DHG tool.
Got a nice big stack of all 3 style trees ****FOR SALE****......

Your choice $60

13 tree (9.5mm) with 1" up-stem(25mm) fits into 75mm tube &

10 tree (9.5mm) with 1" up-stem(25mm) fits into 65mm tube

6 tree (9.5mm) with a 12mm up-stem. fits into 44mm tube

all jigs come with a #10x24 1-1/2" long thumb screw.

[Lampwork49]

Would like to know. Is one better than the other between brass and graphite reamers?? Is there some advantage to one?? Would really like to know. Thx

[maxtsunami]

Would like to know. Is one better than the other between brass and graphite reamers?? Is there some advantage to one?? Would really like to know. Thx

Brass doesn't break as easily as graphite, and graphite chips and wears down when brass doesn't.

How much is shipping?

[Dawg House Glass]

Yes it has more duribility for sure but it also is a personal preferance at times as well. I use bith graphite and brass but prefer the brass for the weight and longevity of the tool. Shipping is 6.00 priority mail in the US and priced accordingly to other countries. Hope this helps.

[Shonbal]

These tools kick ass, I have a bunch of them. The biggest difference between graphite and brass is the fact that you can't really put your brass tools in the fire. I also think I get a much thicker bowl when using brass bowl pushes.

[Jim OShea]

I have a 14mm brass joint shaping tool and if Im not quick enough the handle gets way to hot to hold in my hand and then i have to use a male joint with beeswax to get a nice fit or wait for the tool to cool down

[JBob]

If you are not quick enough? I have not used this tool, so im not really endorsing it, but id like to give it a shot. However, i currently ream out my tubing to get it to the approximate taper (just a bit bigger) then i heat it all up and marver it around a GonG holding, or in this case, shaping tool...I would still use a real ground joint to test it though as the holders always have felt slippery. how long are u using this for at a time? how much time is it spending in the molten glass to get that hot? how much if any time are u spending in the flame? i didnt think this would exactly be too big of an issue after u get the proper process down..

[Dawg House Glass]

Jim Oshea, If the brass handle on the tool is getting too hot to touch you are working way more than you ever should in the flame. Spend a little more time with your regular brass or graphite reamers getting your piece more to your desired shape before using the OG tool to finalize your shape and fit. I use mine on a daily basis and have never had to put my tool down due too it being too hot to hold. Bees wax the tool after each joint shaping and I always have a bees waxed male joint on hand too double check that final fit after the OG shape to insure it is complete. Hope this helps.
Dawg

[JBob]

you should create a long tapered octagonal reamer with notches marking approximately where the 14mm and 18mm fittings belong, sort of a precourser to the GonG shaping tool which is more like a mold really...would be a nice set, notched reamer and 2 gong tools...id buy it!

[Jim OShea]

Jim Oshea, If the brass handle on the tool is getting too hot to touch you are working way more than you ever should in the flame. Spend a little more time with your regular brass or graphite reamers getting your piece more to your desired shape before using the OG tool to finalize your shape and fit. I use mine on a daily basis and have never had to put my tool down due too it being too hot to hold. Bees wax the tool after each joint shaping and I always have a bees waxed male joint on hand too double check that final fit after the OG shape to insure it is complete. Hope this helps.
Dawg

Thanks, i never put the brass in the flame though and i do everything you say. I just started flameworking this year so im not the quickest but i am getting better. sometimes if i dont get it to fit perfect the first time i can feel the heat traveling up the handle when i go to use it again. I probably just need to practice more.

[Logan]

Excellent quality tools! Got a 19mm joint shaping tool. Working with it today, trying to get the hang of using it. Some how to videos on your joint shaping tools would be an excellent resource, probably good advertisement too.

[Logan]

Love the joint shaping tool! Its a game changer for sure. Can you make a brass female for making male joints?

[Dawg House Glass]

Logan, I have had a few requests but have not designed anything.

[Homegrown Handblown]

Id take male/female sets in 14 and 19 if I you come up with them
cheers!

[Dawg House Glass]

Homegrown Handblown,
I have the female joint shaping tools ready to ship now. Message me when you are ready.

[Dawg House Glass]

Time to buy yourself something for Christmas this year right?????
Sale goes through to Dec 15th. Hit me up with a pm on what you need and your email and I can invoice thru paypal.

[SlyAirbrush.com]

Hey Twisted I need a 3/4" brass reamer 2mm-19mm 5" long you can paypal me a donteairbrush@gmail.com or call 4076920558 Thanks

[JBob]

I hit him up on FB last night still waiting for a reply to pick up a few reamers

[Dawg House Glass]

Sorry i was out of town. Sent you a paypal request this morning. Thanks again for the support!
Dawg

[Jiggy Boro]

Do the brass gong holders suck out the heat of the glass like graphite ones do?